2Wire 1000 Series Residential Gateways are bundled with several powerful applications including: Fine-grained Content Screening, Usage Monitoring and Parental Control applications capable of filtering/blocking objectionable content (based on Content Categories and URL based Access Control Lists or ACLs), Active Stateful Packet Inspection Firewall Monitor for continuous threat assessment (using Application Lists and ALG), software tools for allowing web-based (protected) remote computer access to your computers, and support for Automated web-based software/firmware update.

2Wire HomePortal® 1000 Series Broadband Gateways : Features & Factory Default Settings:

• Broadband Interface: ADSL modem (ADSL2 ready) included in 2Wire gateway model# 1070, 1000HG, 1700SG, 1700HG, and 1800HG. Ethernet on 2Wire model # 170HG, and 180HG. Several broadband protocols supported including: PPPoE, PPPoA, RFC2684, DHCP client, Multi-IP support; Transparent Bridging; and ATM Adaptation Layer 2 & 5 for up to 10 Permanent Virtual Circuits (PVCs).
  
• Ethernet Ports: Four Ethernet (10/100 with Auto-crossover) ports on all of the above –except for only 1 Ethernet port on 2Wire model # 1070, and 1000HG.
  
• Wireless Enabled: HyperG included on 2Wire model # 1000HG, 1700HG, 1800HG, 170HG and 180HG. IEEE 802.11g AP included on 1700HG. Wireless not available on 2Wire model 1070 gateway.
  
• USB: Not available on any of the 2Wire 1000 series gateways.
  
• Voice Over IP: Not available on any of the 2Wire 1000 series gateways.
  
• Default Username / UserID on 2Wire Routers: None
  
• Default Password on 2Wire Routers: Wireless
  
• Default IP Address on 2Wire Routers: http://home/
  
• Default Netmask on 2Wire Routers: 255.255.255.0
  
• Default SSID on 2Wire Routers: 2WIRExxx (where xxx is the last three digits of the products serial number that can be found on the bottom of the your 2Wire HomePortal. Supports Multi SSID.
  
• Default WEP Key on 2Wire Routers: These devices support Wi-Fi Protected Access (WPA-PSK), and 64-bit / 128-bit WEP. For WEP information, got to the "Wireless Settings " section under the "Home Network" tab. If the router obscures the WEP key display (by showing a bunch of ******* for the WEP key), you may have to enter a (ASCII or Hexadecimal) new WEP key. Set it use "Shared" WEP key.
  
• Applies to 2Wire Product Model#: 1070, 1000HG, 1700SG, 1700HG, 1800HG, 170HG, and 180HG ADSL gateways.
  
• Default Access Method: HTTP
  
• Access Level: Full Administrator level access

  Please note: You may need to manually configure your Nintendo DS based on factory default settings used in different versions of 2Wire Firmware/Software. This document shows you factory default settings needed for manually configuring your Nintendo DS for different versions of 2Wire software.

These 2Wire Broadband (Advanced DSL) Gateways not only offer excellent routing capabilities including support for Network Address Translation (NAT), and Network Port Translation (PAT); they also have a built-in DHCP Server, DNS Proxy, VPN pass-thru capabilities, and support for a Static Routes Table. Most of these carrier grade (TR-069 compliant) 2Wire gateways have an integrated ADSL modem, as well as a built-in HyperG/802.11g wireless access point. These Component Management System (CMS) standards based devices allow for in-situ firmware upgrades, and remote CPE diagnosis -features that are not only helpful to the consumers, but critical for the carriers when it comes to cost-effectively activating, provisioning, and maintaining differentiated broadband services -right from the Telco/Carrier Central Office.